How to Safely Adjust Your Own Eyeglasses: A Step‑by‑Step Guide

When a pair of eyeglasses sits comfortably, you hardly notice them. But crooked frames, slipping lenses, or a misaligned nose pad can turn your glasses into a daily nuisance.

Learning how to make minor adjustments yourself can save a trip to the optical shop and eliminate the need to ship the frames back to the manufacturer. A basic eyeglass repair kit, a little patience, and the right technique are all you need for most small fixes. However, knowing when to hand the job over to a professional is equally important.

Before you touch your glasses, evaluate the fit. Stand in front of a mirror and note any asymmetry—whether a temple is lower than the other or the nose pads sit too high or too low.

The State University of New York College of Optometry advises that the top of the frame should sit just below the eyebrows; it should not sit too high or too low, ensuring the optical centers of the lenses align with your eyes.

Once you’ve identified the problem, you can begin minor repairs.

Most crookedness stems from a bent temple (also called an arm). To check the angle, place the glasses on a flat surface so the rims rest evenly. If one temple’s tip does not touch the table, that arm needs to be bent downward; if one rim lifts off the surface, the opposite arm likely needs to be raised.

Adjusting plastic temples: Warm the bent arm by holding it over a pot of steaming water or by briefly running it under warm tap water. After it cools, gently bend the arm back into place using two fingers—one to hold the hinge and the other to guide the tip. Stop immediately if you feel resistance to avoid a break.

“If you adjust glasses yourself, be gentle and work slowly,” advises Bosung Kim, OD, of Della Optique Eyewear & Optometry in Vancouver. “Rushing can snap the arm or shift the lenses out of alignment, which then requires professional repair.”

Never use an open flame or a hair dryer on the frames; excessive heat can damage lens coatings, warns Kelli Conesa, OD, CEO of Chrycy Eye Group in Miami.

Adjusting metal frames: Warm metal arms with steam or warm water to increase pliability, but many minor bends can be corrected without heat. Keep the glasses on a flat surface and re‑check alignment after each adjustment.

If a temple feels too tight against your ear, bend the end upward so it forms roughly a 45‑degree angle just behind the ear. For a loose temple, grip the bend and gently pull the arm downward. Test the fit repeatedly; small, incremental changes prevent over‑bending.

Hinges are secured by tiny screws. Repeated opening and closing can loosen these screws, and a missing screw often means a replacement is needed.

Most repair kits include a set of standard screws, a miniature screwdriver (magnetized versions are ideal), cleaning cloth, and spare nose pads. To tighten a hinge, line up the holes, insert the screw, and turn clockwise until it stops turning easily—do not overtighten.

“Work in a well‑lit, clutter‑free area and use a magnifier if needed,” recommends Tampa‑area optometrist Nora Cothran, OD. “Tighten screws slowly to avoid stripping the threads or damaging the frame.”

Adjusting nose pads:

  • Hold one pad between thumb and forefinger (or use needle‑nose pliers) while stabilizing the opposite temple.
  • Gently bend the pad inward to tighten, or outward to loosen, adjusting each side separately.
  • Never pinch both pads together at once.

The same principles apply to children’s glasses—ensure a snug but comfortable fit so the frames stay in place during activity without causing pressure points. If the frames no longer span the width of the child’s face or the temples bow outward, it’s likely time for a new pair.

Two major risks of DIY adjustments are damaging the frame beyond repair and misaligning the lenses, which can impair vision. If your glasses are under warranty, a botched repair could void that coverage.

While many optical shops will perform these minor tweaks for free or at minimal cost, especially if you purchased the frames from them, consider professional help for anything beyond simple bends. “I do not recommend buying repair kits unless you’re comfortable with basic adjustments,” says Conesa. “Optical labs have specialized tools that eliminate the risk of frame damage.”

Lens issues—scratches, cracks, or coating problems—should always be addressed by an optician or ophthalmologist. Cracked lenses cannot be repaired; they must be replaced.

Properly fitted glasses keep the optical center of each lens aligned with your eyes, reducing eye strain, headaches, and fatigue, notes San Diego ophthalmologist Angelique Pillar, MD.

Beyond vision clarity, a good fit matters for:

  • Comfort: Prevents pressure‑induced headaches or nose pain.
  • Safety: Reduces the chance of glasses slipping or falling during activities.
  • Appearance: Well‑fitted frames look polished and boost confidence.

When buying glasses, especially online, a professional fitting can make the difference between a perfect pair and a constant adjustment cycle. The Vision Council reported that in 2020, 14 % of U.S. eyeglass sales were online, yet a British study found consumers prefer in‑store purchases because of fit issues.

“Style is important, but it must be paired with a proper fit,” warns James Dello Russo, OD, of New Jersey Eye Care Center. “Skipping the fitting step can lead to sub‑optimal vision and frequent returns.”

In summary, a basic repair kit can handle lost screws, loose nose pads, and minor temple bends. However, avoid excessive force, use gentle heat only when appropriate, and seek professional assistance for anything beyond a simple tweak. Most optical shops will perform these adjustments at little or no charge.

If you’re ever unsure, bring your glasses to a qualified optician—your eyesight and your frames will thank you.

Eye & Vision Disorders - Related Articles